- Evoluerende wereldwijde normen versnellen de noodzaak voor OEM’s van dieselmotoren om aanvullende emissiebeperkende strategieën toe te passen
GALESBURG, Mich.-(BUSINESS WIRE)- Het energiemanagementbedrijf Eaton heeft vandaag aangekondigd dat zijn Vehicle Group heeft aangetoond dat cilinder deactivering (CDA) een effectieve technologie is om te voldoen aan toekomstige wereldwijde emissie-eisen voor bedrijfsvoertuigen met dieselmotoren. Tot nu toe is de technologie geëvalueerd met een nauw gekoppeld nabehandelingssysteem met selective catalytic reduction (SCR) met en zonder een 48-volt elektrisch verwarmingselement.
Dit persbericht bevat multimedia. Bekijk het volledige persbericht hier: https://www.businesswire.com/news/home/20211116005234/en/
Eaton Leverages Cylinder Deactivation and Exhaust Thermal Management Technologies to Reduce Commercial Vehicle Emissions
- Evolving global standards accelerate the need for diesel engine OEMs to employ additional emissions-reduction strategies
GALESBURG, Mich.–(BUSINESS WIRE)– Power management company Eaton today announced its Vehicle Group has demonstrated cylinder deactivation (CDA) as an effective technology for meeting future global emissions requirements for diesel-engine powered commercial vehicles. To date, the technology has been evaluated with a close-coupled selective catalytic reduction (SCR) aftertreatment system with and without a 48-volt electric heater.
This press release features multimedia. View the full release here: https://www.businesswire.com/news/home/20211116005234/en/
Eaton has demonstrated its cylinder deactivation technology is effective for meeting future global emissions requirements for diesel-engine powered commercial vehicles. (Photo: Business Wire)
“Our CDA technology has proven it can help our customers meet increasingly strict emissions regulations for diesel engines,” said Christopher Mancuso, business unit director, Engine Air Management, Eaton’s Vehicle Group. “This comes at a time when many global manufacturers are determining what technologies they will leverage in next-generation vehicles to reduce harmful emissions.”
New emissions regulations spearheaded by the California Air Resources Board (CARB), U.S. Environmental Protection Agency (EPA) and European Commission (EC) are slated for adoption in coming years. These agencies, in concert with other national and international regulators, seek to significantly reduce greenhouse gas (GHG) emissions and harmful air pollutants produced primarily by heavy-duty trucks, vans and buses.
Rapid catalyst warm-up essential
Eaton partnered with the Southwest Research Institute (SwRI), one of the oldest and largest independent, nonprofit, applied research and development organizations in the U.S., to demonstrate the feasibility of its Vehicle Group’s technology. The findings demonstrate that using CDA and a close-coupled SCR catalyst reduced both nitrous oxide (NOx) and carbon dioxide (CO2) emissions with fuel consumption savings of up to 40% at idle.
Previous results utilizing CDA and a close-coupled SCR catalyst demonstrated compliance to forthcoming U.S. regulations for NOx and CO2 emissions for diesel commercial vehicles. Testing with the new low-load cycle (LLC) resulted in a 5% drop in CO2 while dramatically reducing NOx. The assessment was developed by CARB to replicate real-world urban tractor and vocational vehicle operations at low engine loads.
Eaton’s 2021 testing with SwRI showed further advancement, dropping NOx levels by 99.4% on the composite federal test procedure (FTP) and lowering the LLC NOx to well within current guidelines. Notably, using the same aftertreatment system with the addition of a 48-volt electric heater located upstream of the SCR further achieved a reduction in CO2.
CDA technology can benefit vehicle manufacturers facing tightening emissions standards in Europe as well. The next set of requirements, known as Euro VII for heavy-duty trucks, is targeted for the second part of the decade. In the U.S., CARB is introducing more stringent regulations as soon as 2024, while the EPA has circled 2027 to begin applying stricter emissions limits on new-model heavy-duty vehicles. Collectively, these standards are designed to reduce tailpipe NOx emissions up to 90%, accelerating the need for global engine manufacturers to employ additional emissions-reduction strategies such as electric catalyst heating. This technology is an example of how Eaton is progressing toward achieving its 2030 Sustainability Targets. By 2030, the company aims to reduce emissions from its solutions and throughout its value chain by 15%.
Eaton’s mission is to improve the quality of life and the environment through the use of power management technologies and services. We provide sustainable solutions that help our customers effectively manage electrical, hydraulic, and mechanical power – more safely, more efficiently, and more reliably. Eaton’s 2020 revenues were $17.9 billion, and we sell products to customers in more than 175 countries. We have approximately 85,000 employees. For more information, visit www.eaton.com.
(216) 333-2876 (cell)